Windows Permits in Nashville, TN

Date: Aug 27, 2014

Permit type: Windows

Description: Description - construct rear addition roofing - roofing material shall be asphalt composite shingles. color shall match existing or if not, it shall be approved by the mhzc prior to purchase. - gutters shall be simple metal gutters. windows & doors - windows shall have single-light or fully-simulated, divided-light sashes. muntins are to be factory installed with an exterior muntin, interior muntin, and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. double and triple windows shall have a 4" to 6" mullion between. - door manufacturer and type must be approved by mhzc staff prior to installation. - four (4) inch (nominal) wood casings are required around doors, windows, and vents within clapboard walls. - windows on clapboard structures shall not have brick-mold. siding & trim - siding and trim shall be wood or smooth-faced, cement-fiberboard (e.g.: hardiplank). if siding exposure is not matched to that of the existing house, then it shall have a maximum reveal of five (5) inches. - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner. hvac - hvac/mechanical/utility vents, pipes, lines, and all associated components, condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. general specifications - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to continuing with the project.

Client: Moore, Matthew Rodney & Callie Stydahar

Parcel #: 08309046000

Permit #: HCPERMIT 201400329

Contractor: Ole South Properties, Inc.

Date: Sep 8, 2014

Permit type: Windows

Description: Construct new garage cladding & trim - siding shall be smooth-faced cement-fiberboard with a four inch (4") exposuure. - all/any trim, railings, vents and associated type elements are to be wood or cement fiberboard. clad material is not approved. wood or cement fiberboard shall be a smooth face material void of any simulated wood grain pattern or rough, unfinished appearance. all exposed exterior lumber should be grade number #1 or #2. lower grade lumber is unsuitable for exterior work. - 2 x 4 inches wood corner boards are typical on the face of each exposed corner, except for masonry buildings. lumber to be of an appropriate trim grade (smooth and square). stud wall lumber is not appropriate. - 2 x 4 inches wood casing typical at doors and windows, except for masonry buildings. double and triple windows should have a 4" to 6" mullion between. lumber to be of an appropriate trim grade (smooth and square). stud wall lumber is not appropriate. windows & doors - if there are muntins, only factory installed muntins are approved. self installed snap, clip or glue type muntins on windows are not approved. interior type muntins on windows are not approved. windows to be approved by staff prior to installation. - windows on clapboard structures shall not have brick-mold. - overhead garage door and pedestrian entry doors may be steel with simple panel design. doors to be approved by staff prior to installation. roof - roof material may match the main structure. if roof material is not to match main structure, then color to be approved by staff prior to installation. general specifications - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. - all measurements and relationships of existin

Client: Fabling, Justin & Katherine

Parcel #: 10308019000

Permit #: HCPERMIT 201400354

Contractor: Cary Electric

Date: Sep 15, 2014

Permit type: Windows

Description: Restrictive covenant for detached structure recorded 201409080081786. construct a 16'x24' detached garage vinyl siding 6x7 ohd 1 walk door 5 3.o windows 60a electric asphalt shingles gutters and downspouts. not to be used for living or commercial purposes. maallowed height is 16'. 10' min rear s/b per easement on recorded sub plat; 5' min side s/b. need to record instrument for trade permits. pursuant to ordinance no. 2006-1263 of the metropolitan code of laws i (the holder on this permit) hereby certify that all construction and demolition waste generated by any and all activities governed by this permit shall be disposed of in an approved landfill. further i certify that no construction and demolition waste shall be stored on the property in violation of any provision of the metropolitan code.

Fee: $76.73 paid to City of Nashville, Tennessee

Client: Murphree Joseph Wade & Jill

Parcel #: 16003006600

Permit #: CAEL 201433892

Contractor: James H Pfeffer

Date: Sep 18, 2014

Permit type: Windows

Description: - construct two-story house and detached one-story carport.| roofing | - roofing material shall be composite asphalt shingles. | - roofing color must be approved by mhzc staff prior to installation. | - gutters shall be simple metal gutters. | windows & doors| - windows shall be wood or aluminum clad wood windows with single-light or fully-simulated divided-light sashes. muntins are to be factory installed |with an exterior muntin interior muntin and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. for double or triple windows there shall be a 4" to 6" mullion between. | - doors shall be full-light or half-light doors. door manufacturer and type must be approved by mhzc staff prior to installation. | - wood brick mold is only appropriate around doors and windows within masonry walls. | - 4 inches (nominal) wood casings are required around doors and windows within clapboard walls. | siding & trim| - primary exterior material will be brick. color and texture must be approved by mhzc staff prior to purchase.| - secondary siding material shall be wood or smooth-faced cement-fiberboard siding (ex. hardiplank) with a maximum reveal of 5 inches. | - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner of clapboard walls.| hvac | - hvac/mechanical/utility vents pipes lines and all associated components condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. | walkways driveways and parking pads | - walkway shall be concrete. | general specifications| - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. | - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to continuing with the project. | - any substitutions or deviation from the approved work requires further review and approval by the mhzc prior to work being undertaken. | - the work items listed are approved in accordance with the adopted design guidelines and are not applicable beyond the unique facts and circumstances of this particular application. | - this permit becomes invalid twelve months after issue date. expired permits must be reissued prior to work being undertaken. | approval of design should not be considered approval of a particular use.| - this is not a building permit. no work can begin without the appropriate review and approval by the metropolitan department of codes administration: howard school building campus (615) 862-6500. |.

Parcel #: 10415049600

Permit #: HCN 201400351

Date: Sep 18, 2014

Permit type: Windows

Description: | description| build rear addition to house.| roofing| - roofing material shall be asphalt composite shingles. color shall match existing or if not it shall be approved by the mhzc prior to purchase. | - gutters shall be simple metal gutters. | windows & doors| - windows shall have single-light or fully-simulated divided-light sashes. muntins are to be factory installed with an exterior muntin interior muntin and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. double and triple windows shall have a 4" to 6" mullion between. | - door manufacturer and type must be approved by mhzc staff prior to installation. | - four (4) inch (nominal) wood casings are required around doors windows and vents within clapboard walls. | - windows on clapboard structures shall not have brick-mold. | siding & trim| - siding and trim shall be wood or smooth-faced cement-fiberboard (e.g.: hardiplank). if siding exposure is not matched to that of the existing house then it shall have a maximum reveal of five (5) inches. | - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner. | hvac | - hvac/mechanical/utility vents pipes lines and all associated components condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. | general specifications| - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. | - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to continuing with the project. | - any substitutions or deviation from the approved work requires further review and approval by the mhzc prior to work being undertaken. | - the work items listed are approved in accordance with the adopted design guidelines and are not applicable beyond the unique facts and circumstances of this particular application. | - this permit becomes invalid twelve months after issue date. expired permits must be reissued prior to work being undertaken. | - removal of cladding windows and roofing on the existing building all-together is partial-demolition and must be reviewed by the mhzc prior to work taking place. | |approval of design should not be considered approval of a particular use. - this is not a building permit. no work can begin without the appropriate review and approval by the metropolitan department of codes administration: howard school building campus (615) 862-6500. |.

Parcel #: 08306006200

Permit #: HCN 201400360

Contractor: James H Pfeffer

Date: Sep 18, 2014

Permit type: Windows

Description: Description build rear addition to house. roofing - roofing material shall be asphalt composite shingles. color shall match existing or if not, it shall be approved by the mhzc prior to purchase. - gutters shall be simple metal gutters. windows & doors - windows shall have single-light or fully-simulated, divided-light sashes. muntins are to be factory installed with an exterior muntin, interior muntin, and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. double and triple windows shall have a 4" to 6" mullion between. - door manufacturer and type must be approved by mhzc staff prior to installation. - four (4) inch (nominal) wood casings are required around doors, windows, and vents within clapboard walls. - windows on clapboard structures shall not have brick-mold. siding & trim - siding and trim shall be wood or smooth-faced, cement-fiberboard (e.g.: hardiplank). if siding exposure is not matched to that of the existing house, then it shall have a maximum reveal of five (5) inches. - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner. hvac - hvac/mechanical/utility vents, pipes, lines, and all associated components, condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. general specifications - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to continuing with the project.

Client: Buhrman, Christopher D. & Abigail C.

Parcel #: 08306006200

Permit #: HCPERMIT 201400360

Contractor: Pfeffer Torode Architecture Pllc

Date: Oct 16, 2014

Permit type: Windows

Description: - construct two-story house and detached one-story carport.| roofing | - roofing material shall be composite asphalt shingles. | - roofing color must be approved by mhzc staff prior to installation. | - gutters shall be simple metal gutters. | windows & doors| - windows shall be wood or aluminum clad wood windows with single-light or fully-simulated divided-light sashes. muntins are to be factory installed |with an exterior muntin interior muntin and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. for double or triple windows there shall be a 4" to 6" mullion between. | - doors shall be full-light or half-light doors. door manufacturer and type must be approved by mhzc staff prior to installation. | - wood brick mold is only appropriate around doors and windows within masonry walls. | - 4 inches (nominal) wood casings are required around doors and windows within clapboard walls. | siding & trim| - primary exterior material will be brick. color and texture must be approved by mhzc staff prior to purchase.| - secondary siding material shall be wood or smooth-faced cement-fiberboard siding (ex. hardiplank) with a maximum reveal of 5 inches. | - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner of clapboard walls.| hvac | - hvac/mechanical/utility vents pipes lines and all associated components condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. | walkways driveways and parking pads | - walkway shall be concrete. | general specifications| - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. | - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to continuing with the project. | - any substitutions or deviation from the approved work requires further review and approval by the mhzc prior to work being undertaken. | - the work items listed are approved in accordance with the adopted design guidelines and are not applicable beyond the unique facts and circumstances of this particular application. | - this permit becomes invalid twelve months after issue date. expired permits must be reissued prior to work being undertaken. | approval of design should not be considered approval of a particular use.| - this is not a building permit. no work can begin without the appropriate review and approval by the metropolitan department of codes administration: howard school building campus (615) 862-6500. |.

Parcel #: 10415049600

Permit #: HCN 201400385

Date: Oct 16, 2014

Permit type: Windows

Description: | description| - construct ridge raise rear addition and side addition; setback determination. | roofing| - roofing material shall be asphalt composite shingles. color shall match existing or if not it shall be approved by the mhzc prior to purchase. | - gutters shall be simple metal gutters. | windows & doors| - windows shall have single-light or fully-simulated divided-light sashes. muntins are to be factory installed with an exterior muntin interior muntin and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. double and triple windows shall have a 4" to 6" mullion between. | - door manufacturer and type must be approved by mhzc staff prior to installation. | - four (4) inch (nominal) wood casings are required around doors windows and vents within clapboard walls. | - windows on clapboard structures shall not have brick-mold. | siding & trim| - siding and trim shall be wood or smooth-faced cement-fiberboard (e.g.: hardiplank). if siding exposure is not matched to that of the existing house then it shall have a maximum reveal of five (5) inches. | - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner. | hvac | - hvac/mechanical/utility vents pipes lines and all associated components condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. | general specifications| - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. | - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to continuing with the project. | - any substitutions or deviation from the approved work requires further review and approval by the mhzc prior to work being undertaken. | - the work items listed are approved in accordance with the adopted design guidelines and are not applicable beyond the unique facts and circumstances of this particular application. | - this permit becomes invalid twelve months after issue date. expired permits must be reissued prior to work being undertaken. | - removal of cladding windows and roofing on the existing building all-together is partial-demolition and must be reviewed by the mhzc prior to work taking place. | |approval of design should not be considered approval of a particular use. - this is not a building permit. no work can begin without the appropriate review and approval by the metropolitan department of codes administration: howard school building campus (615) 862-6500. |.

Parcel #: 10308019000

Permit #: HCN 201400389

Contractor: Regent Homes, Llc.

Date: Oct 16, 2014

Permit type: Windows

Description: Description - construct ridge raise, rear addition, and side addition; setback determination. roofing - roofing material shall be asphalt composite shingles. color shall match existing or if not, it shall be approved by the mhzc prior to purchase. - gutters shall be simple metal gutters. windows & doors - windows shall have single-light or fully-simulated, divided-light sashes. muntins are to be factory installed with an exterior muntin, interior muntin, and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. double and triple windows shall have a 4" to 6" mullion between. - door manufacturer and type must be approved by mhzc staff prior to installation. - four (4) inch (nominal) wood casings are required around doors, windows, and vents within clapboard walls. - windows on clapboard structures shall not have brick-mold. siding & trim - siding and trim shall be wood or smooth-faced, cement-fiberboard (e.g.: hardiplank). if siding exposure is not matched to that of the existing house, then it shall have a maximum reveal of five (5) inches. - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner. hvac - hvac/mechanical/utility vents, pipes, lines, and all associated components, condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. general specifications - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported

Client: Fabling, Justin & Katherine

Parcel #: 10308019000

Permit #: HCPERMIT 201400389

Date: Oct 22, 2014

Permit type: Windows

Description: | build rear dormer iaw attached plans. | roof| - roof material to match the main structure. eave depth profile and details to match that of the existing structure. | - gutter work to match existing structure. | - roof ridgeline to be below the level of the ridgeline of the main structure. | location| - dormer to be constructed on roof so that structure sits back a minimum of 24 inches from the wall of the floor below. | windows| - muntins are to be factory installed with an exterior muntin interior muntin and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. | - windows on clapboard structures shall not have brick-mold. | cladding & trim| - trim and cladding shall be wood or cement fiberboard with a smooth face void of any simulated wood grain pattern or rough unfinished appearance. simulated wood stamp is not appropriate. | - all exposed exterior lumber should be grade number #1 or #2. lower grade lumber is unsuitable for exterior work. | - if cladding material/exposure does not match the main structure then lap siding to be 6-width material with a maximum of 5 inches of exposure. | - 2 4 inches wood corner boards are typical on the face of each exposed corner. lumber to be of an appropriate trim grade (smooth and square). stud wall lumber is not appropriate. | - 2 4 inches wood casing typical at doors and windows. lumber to be of an appropriate trim grade (smooth and square). stud wall lumber is not appropriate. | general specifications| - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. | - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to continuing with the project. | - any substitutions or deviation from the approved work requires further review and approval by the mhzc prior to work being undertaken. | - the work items listed are approved in accordance with the adopted design guidelines and are not applicable beyond the unique facts and circumstances of this particular application. | - this permit becomes invalid twelve months after issue date. expired permits must be reissued prior to work being undertaken. | | - this is not a building permit. no work can begin without the appropriate review and approval by the metropolitan department of codes administration: howard school building campus (615) 862-6500. |.

Parcel #: 08303010500

Permit #: HCN 201400416

Contractor: Regent Homes, Llc.

Date: Oct 24, 2014

Permit type: Windows

Description: Exterior repairs including replacement of roofing and repair/replacement of gutters, fascia, soffit subject to final approval of mhzc staff. roofing - roofing material shall be asphalt composite shingles. color shall match existing or if not, it shall be approved by the mhzc prior to purchase. - gutters shall be simple metal gutters. windows & doors - windows shall have single-light or fully-simulated, divided-light sashes. muntins are to be factory installed with an exterior muntin, interior muntin, and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. double and triple windows shall have a 4" to 6" mullion between. - door manufacturer and type must be approved by mhzc staff prior to installation. - four (4) inch (nominal) wood casings are required around doors, windows, and vents within clapboard walls. - windows on clapboard structures shall not have brick-mold. siding & trim - siding and trim shall be wood or smooth-faced, cement-fiberboard (e.g.: hardiplank). if siding exposure is not matched to that of the existing house, then it shall have a maximum reveal of five (5) inches. - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner. hvac - hvac/mechanical/utility vents, pipes, lines, and all associated components, condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. general specifications - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. ina

Client: Honeycutt, Alexanderia Elizabeth

Parcel #: 09609011900

Permit #: HCPERMIT 201400418

Contractor: Titan Electric, Llc.

Date: Oct 24, 2014

Permit type: Windows

Description: To construct a new single family res at 3548 sqft with attached garage at 503 with 326 porches.this is one of two single family houses on this property.split from 131-3-237.lot size 15045 sqft.coverage at 35%.garage doors face each other.see plan.max ht at 3 stories and 45'.pursuant ordinance # 2006-1263 metropolitan code of laws i (the holder on this permit) hereby certify that all construction & demolition waste generated by any & all activities governed by this permit shall be disposed of in an approved landfill. further i certify that no construction & demolition waste shall be stored on the property in violation of any provision of metropolitan code. *********************************************site plan sent to file. per plat note 5--- min ffe 596.5 also baywindows not allowed to encroach in setbacks.

Fee: $164.75 paid to City of Nashville, Tennessee

Parcel #: 131033A90000CO

Permit #: CAEL 201439716

Contractor: Ole South Properties, Inc.

Date: Nov 4, 2014

Permit type: Windows

Description: Construct rear addition and replace side windows with a door description roofing - roofing material shall be asphalt composite shingles. color shall match existing or if not, it shall be approved by the mhzc prior to purchase. - gutters shall be simple metal gutters. windows & doors - windows shall have single-light or fully-simulated, divided-light sashes. muntins are to be factory installed with an exterior muntin, interior muntin, and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. double and triple windows shall have a 4" to 6" mullion between. - door manufacturer and type must be approved by mhzc staff prior to installation. - four (4) inch (nominal) wood casings are required around doors, windows, and vents within clapboard walls. - windows on clapboard structures shall not have brick-mold. siding & trim - siding and trim shall be wood or smooth-faced, cement-fiberboard (e.g.: hardiplank). if siding exposure is not matched to that of the existing house, then it shall have a maximum reveal of five (5) inches. - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner. hvac - hvac/mechanical/utility vents, pipes, lines, and all associated components, condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. general specifications - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to

Client: Ryan, Tyler M. & Ashley M.

Parcel #: 10308018600

Permit #: HCPERMIT 201400432

Contractor: Titan Electric, Llc.

Date: Nov 4, 2014

Permit type: Windows

Description: To construct a new single family res at 3558 sqft with attached garage at 501 with 326 porches.this is one of two single family houses on this property.split from 131-3-237.lot size 15045 sqft.coverage at 35%.garage doors face each other.see plan.max ht at 3 stories and 45'.pursuant ordinance # 2006-1263 metropolitan code of laws i (the holder on this permit) hereby certify that all construction & demolition waste generated by any & all activities governed by this permit shall be disposed of in an approved landfill. further i certify that no construction & demolition waste shall be stored on the property in violation of any provision of metropolitan code. *********************************************site plan sent to file. per plat note 5--- min ffe 596.5 also baywindows not allowed to encroach in setbacks.

Fee: $154.52 paid to City of Nashville, Tennessee

Parcel #: 131033A00100CO

Permit #: CAEL 201441457

Contractor: Dove Construction, Llc

Date: Nov 5, 2014

Permit type: Windows

Description: Construct a rear porch addition description roofing - roofing material shall be asphalt composite shingles. color shall match existing or if not, it shall be approved by the mhzc prior to purchase. - gutters shall be simple metal gutters. windows & doors - windows shall have single-light or fully-simulated, divided-light sashes. muntins are to be factory installed with an exterior muntin, interior muntin, and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. double and triple windows shall have a 4" to 6" mullion between. - door manufacturer and type must be approved by mhzc staff prior to installation. - four (4) inch (nominal) wood casings are required around doors, windows, and vents within clapboard walls. - windows on clapboard structures shall not have brick-mold. siding & trim - siding and trim shall be wood or smooth-faced, cement-fiberboard (e.g.: hardiplank). if siding exposure is not matched to that of the existing house, then it shall have a maximum reveal of five (5) inches. - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner. hvac - hvac/mechanical/utility vents, pipes, lines, and all associated components, condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. general specifications - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to continuing with the project.

Client: Assad, Tufik R. & Kristen M.

Parcel #: 10308023100

Permit #: HCPERMIT T201400443

Contractor: Ole South Properties, Inc.

Date: Nov 20, 2014

Permit type: Windows

Description: New construction-infill. roofing - roofing material shall be composite asphalt shingles. - roofing color must be approved by mhzc staff prior to installation. - gutters shall be simple metal gutters. windows & doors - windows shall be wood or aluminum clad wood windows with single-light or fully-simulated, divided-light sashes. muntins are to be factory installed with an exterior muntin, interior muntin, and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. for double or triple windows, there shall be a 4" to 6" mullion between. - doors shall be full-light wood doors. door manufacturer and type must be approved by mhzc staff prior to installation. - 4 inches (nominal) wood casings are required around doors and windows within clapboard walls. - wood brick mold is only appropriate around doors and windows within masonry walls. - windows on clapboard structures shall not have brick-mold. siding & trim - exterior finish materials shall be trim grade (smooth and square). stud wall lumber or embossed wood grain is not appropriate. - exterior siding material shall be wood or smooth-faced, cement-fiberboard siding (ex. hardiplank) with a maximum reveal of 5 inches. - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner. hvac - hvac/mechanical/utility vents, pipes, lines, and all associated components, condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. walkways, driveways and parking pads - walkway shall be concrete. general specifications - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. - a

Client: Oliver, William F. & Andrea E.

Parcel #: 08301019800

Permit #: HCPERMIT 201400438

Date: Nov 20, 2014

Permit type: Windows

Description: | new construction-infill.| | roofing | - roofing material shall be composite asphalt shingles. | - roofing color must be approved by mhzc staff prior to installation. | - gutters shall be simple metal gutters. | windows & doors| - windows shall be wood or aluminum clad wood windows with single-light or fully-simulated divided-light sashes. muntins are to be factory installed |with an exterior muntin interior muntin and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. for double or triple windows there shall be a 4" to 6" mullion between. | - doors shall be full-light wood doors. door manufacturer and type must be approved by mhzc staff prior to installation. | - 4 inches (nominal) wood casings are required around doors and windows within clapboard walls. | - wood brick mold is only appropriate around doors and windows within masonry walls. | - windows on clapboard structures shall not have brick-mold. | siding & trim| - exterior finish materials shall be trim grade (smooth and square). stud wall lumber or embossed wood grain is not appropriate. | - exterior siding material shall be wood or smooth-faced cement-fiberboard siding (ex. hardiplank) with a maximum reveal of 5 inches. | - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner.| hvac | - hvac/mechanical/utility vents pipes lines and all associated components condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. | walkways driveways and parking pads | - walkway shall be concrete. | general specifications| - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. | - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to continuing with the project. | - any substitutions or deviation from the approved work requires further review and approval by the mhzc prior to work being undertaken. | - the work items listed are approved in accordance with the adopted design guidelines and are not applicable beyond the unique facts and circumstances of this particular application. | - this permit becomes invalid twelve months after issue date. expired permits must be reissued prior to work being undertaken. | ||approval of design should not be considered approval of a particular use. - this is not a building permit. no work can begin without the appropriate review and approval by the metropolitan department of codes administration: howard school building campus (615) 862-6500. |.

Parcel #: 08301019800

Permit #: HCN 201400438

Contractor: Frank Batson Homes, Inc.

Date: Nov 20, 2014

Permit type: Windows

Description: - new construction - outbuilding description cladding & trim - siding shall be wood clapboard or smooth-faced cement fiberboard. the siding reveal shall match the primary building or be five inches. - all/any trim, railings, vents and associated type elements are to be wood or cement fiberboard. clad material is not approved. wood or cement fiberboard shall be a smooth face material void of any simulated wood grain pattern or rough, unfinished appearance. all exposed exterior lumber should be grade number #1 or #2. lower grade lumber is unsuitable for exterior work. - 2 x 4 inches wood corner boards are typical on the face of each exposed corners. lumber to be of an appropriate trim grade (smooth and square). stud wall lumber is not appropriate. - 2 x 4 inches wood casing typical at doors and windows. double and triple windows should have a 4" to 6" mullion between. lumber to be of an appropriate trim grade (smooth and square). stud wall lumber is not appropriate. windows & doors - if there are muntins, only factory installed muntins are approved. self installed snap, clip or glue type muntins on windows are not approved. interior type muntins on windows are not approved. windows to be approved by staff prior to installation. - windows on clapboard structures shall not have brick-mold. - overhead garage door and pedestrian entry doors may be steel with simple panel design. doors to be approved by staff prior to installation. roof - roof material may match the main structure. if roof material is not to match main structure, then color to be approved by staff prior to installation. general specifications - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. - all measurements and

Client: Baskin, Lisa B.

Parcel #: 10416038800

Permit #: HCPERMIT 201400448

Contractor: A & S Electric, Inc.

Date: Nov 21, 2014

Permit type: Windows

Description: Vanderbilt warehouse***** providing power for new electric gate motor. selective demolition of 4 existing warehouse dock doors and canopies and providing infill construction (stud framing and limited windows); providing egress handrails at exterior stairs; installing new dock leveler at an existing dock door; providing new limited exterior security lighting.for vanderbilt warehouse.selective demolition of 4 existing warehouse dock doors and canopies and providing infill construction (stud framing and limited windows); providing egress handrails at exterior stairs; installing new dock leveler at an existing dock door; providing new limited exterior security lighting.for vanderbilt warehouse.

Fee: $76.73 paid to City of Nashville, Tennessee

Parcel #: 09314047900H3

Permit #: CAEL 201443751

Date: Dec 18, 2014

Permit type: Windows

Description: | construction of a new screen porch and detached accessory dwelling unit.| | roofing| - roofing material shall be asphalt composite shingles. color shall match existing or if not it shall be approved by the mhzc prior to purchase. | - gutters shall be simple metal gutters. | windows & doors| - windows shall have single-light or fully-simulated divided-light sashes. muntins are to be factory installed with an exterior muntin interior muntin and a spacer within the double-paned glass. window manufacturer and type must be approved by mhzc staff prior to installation. double and triple windows shall have a 4" to 6" mullion between. | - door manufacturer and type must be approved by mhzc staff prior to installation. | - four (4) inch (nominal) wood casings are required around doors windows and vents within clapboard walls. | - windows on clapboard structures shall not have brick-mold. | siding & trim| - siding and trim shall be wood or smooth-faced cement-fiberboard (e.g.: hardiplank). if siding exposure is not matched to that of the existing house then it shall have a maximum reveal of five (5) inches. | - 4 inches (nominal) wood corner-boards are required at the face of each exposed corner. | hvac | - hvac/mechanical/utility vents pipes lines and all associated components condensers or boxes shall be located behind the midpoint of the structure on a non-street facade. | general specifications| - alterations to be constructed in accordance with attached elevations. any deviation from the approved plans could result in changes being reversed to reflect the approved drawings. please note: mhzc staff may have added notes to the submitted drawings. | - all measurements and relationships of existing conditions and new construction shall be field checked for accuracy with approved plans at the responsibility of the applicant. inaccuracies or differences should be reported to mhzc staff prior to continuing with the project. | - any substitutions or deviation from the approved work requires further review and approval by the mhzc prior to work being undertaken. | - the work items listed are approved in accordance with the adopted design guidelines and are not applicable beyond the unique facts and circumstances of this particular application. | - this permit becomes invalid twelve months after issue date. expired permits must be reissued prior to work being undertaken. | - removal of cladding windows and roofing on the existing building all-together is partial-demolition and must be reviewed by the mhzc prior to work taking place. | |approval of design should not be considered approval of a particular use. - this is not a building permit. no work can begin without the appropriate review and approval by the metropolitan department of codes administration: howard school building campus (615) 862-6500. |.

Parcel #: 10416037900

Permit #: HCN 201400473