Commercial Contracting Permits in McAllen, TX

Date: Jun 15, 2011

Permit type: Commercial Contracting

Description: Demolishing an abandoned residence to create residential subdivision parcel under 8701 n 10th

Fee: $66.00 paid to City of Mcallen, Texas

Client: Agustina B & Philipi E Fletcher

Parcel #: H255000013000308

Permit #: DEM2011-03868

Date: Jun 16, 2011

Permit type: Commercial Contracting

Description: . sidewalks a) sidewalk alignment must match existing alignment in area or be set a minimum of five-foot from the back of curb. any deviation shall require approval by the city engineer. b) sidewalk shall slope toward the street with a maximum transverse slope of inch per foot (2%), 1-inch above the top of curb, and a maximum longitudinal slope of inch per foot (5%). c) sidewalk shall be 4-foot minimum width when placed at an offset behind the curb, and 5-foot minimum width when placed adjacent to the curb. d) sidewalks and ramps shall be constructed of 4 thick concrete reinforced with 6 x 6 no. 6 gage wire mesh or no. 3 bars @ 8 o.c.e.w. e) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness f) sand backfill required on all sidewalks 3 max. sub-grade shall be compacted to 90% standard proctor. g) contraction joints shall be scored every 6 feet and expansion joints every 30 feet. h) sidewalk shall have a broom finish transverse to the walkway. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) no colored or stained or stamped concrete on city row sidewalks j) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. k) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. l) curb and gutter must be saw cut m) ramps shall be placed at all intersection with roadways or where required by law. l) flatwork is required to meet texas accessibility standards (texas civil statutes, article 9102). any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. additionally, decorative concrete shall require approval of the pattern and finish from the city engineer, or designee, prior to construction residential driveway apron (a) minimum driveway width allowed is 12 ft. and maximum is 25 ft. b) curb cut must be a minimum of 6-feet from a side property line. c) flow line of new gutter shall match existing flow line. d) curb and gutter must be saw cut. e) driveway aprons shall be constructed of concrete with a minimum of 6 inches in thickness, reinforced with 6 x 6 no. 6 wire mesh, no. 3 bars @ 12 o.c.e.w. or no. 4 bars @ 18 o.c.e.w. f) no colored or stained or stamped concrete on city driveway apron g) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness. h) concrete shall have a broom finish. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. j) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. k) sub-grade shall be compacted to 90% standard proctor. l) expansion joint required at property line and intersection with sidewalks. longitudinal expansion joint required at mid-point of driveway if width is greater than 18 feet. m) if a manhole falls within a driveway pad, the manhole lid shall be placed flush with the elevation of the driveway. n) any driveway placed where a drainage bar ditch exists, shall maintain the flow line of the ditch with the placement of a concrete culvert. o) driveway wings shall not exceed a 12:1 slope. p) respect the transverse slope of 2% maximum where the sidewalk crossing is proposed. any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. q) requirements of plat note slope of 1%. in no instance shall site grading on residential or commercial properties adversely affect neighboring properties.

Client: Affordable Homes Of South Texas In

Parcel #: W490000000002300

Permit #: ROW2011-03891

Date: Jun 21, 2011

Permit type: Commercial Contracting

Description: . sidewalks a) sidewalk alignment must match existing alignment in area or be set a minimum of five-foot from the back of curb. any deviation shall require approval by the city engineer. b) sidewalk shall slope toward the street with a maximum transverse slope of inch per foot (2%), 1-inch above the top of curb, and a maximum longitudinal slope of inch per foot (5%). c) sidewalk shall be 4-foot minimum width when placed at an offset behind the curb, and 5-foot minimum width when placed adjacent to the curb. d) sidewalks and ramps shall be constructed of 4 thick concrete reinforced with 6 x 6 no. 6 gage wire mesh or no. 3 bars @ 8 o.c.e.w. e) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness f) sand backfill required on all sidewalks 3 max. sub-grade shall be compacted to 90% standard proctor. g) contraction joints shall be scored every 6 feet and expansion joints every 30 feet. h) sidewalk shall have a broom finish transverse to the walkway. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) no colored or stained or stamped concrete on city row sidewalks j) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. k) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. l) curb and gutter must be saw cut m) ramps shall be placed at all intersection with roadways or where required by law. l) flatwork is required to meet texas accessibility standards (texas civil statutes, article 9102). any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. additionally, decorative concrete shall require approval of the pattern and finish from the city engineer, or designee, prior to construction residential driveway apron (a) minimum driveway width allowed is 12 ft. and maximum is 25 ft. b) curb cut must be a minimum of 6-feet from a side property line. c) flow line of new gutter shall match existing flow line. d) curb and gutter must be saw cut. e) driveway aprons shall be constructed of concrete with a minimum of 6 inches in thickness, reinforced with 6 x 6 no. 6 wire mesh, no. 3 bars @ 12 o.c.e.w. or no. 4 bars @ 18 o.c.e.w. f) no colored or stained or stamped concrete on city driveway apron g) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness. h) concrete shall have a broom finish. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. j) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. k) sub-grade shall be compacted to 90% standard proctor. l) expansion joint required at property line and intersection with sidewalks. longitudinal expansion joint required at mid-point of driveway if width is greater than 18 feet. m) if a manhole falls within a driveway pad, the manhole lid shall be placed flush with the elevation of the driveway. n) any driveway placed where a drainage bar ditch exists, shall maintain the flow line of the ditch with the placement of a concrete culvert. o) driveway wings shall not exceed a 12:1 slope. p) respect the transverse slope of 2% maximum where the sidewalk crossing is proposed. any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. q) requirements of plat note slope of 1%. in no instance shall site grading on residential or commercial properties adversely affect neighboring properties.

Client: Inter National Bank

Parcel #: T544300000000500

Permit #: ROW2011-03998

Contractor: Grimaldos Electric

Date: Jun 22, 2011

Permit type: Commercial Contracting

Description: Ok by ags/mm esi#100-45540446

Fee: $26.00 paid to City of Mcallen, Texas

Permit #: CMM2011-04044

Date: Jun 23, 2011

Permit type: Commercial Contracting

Description: . sidewalks a) sidewalk alignment must match existing alignment in area or be set a minimum of five-foot from the back of curb. any deviation shall require approval by the city engineer. b) sidewalk shall slope toward the street with a maximum transverse slope of inch per foot (2%), 1-inch above the top of curb, and a maximum longitudinal slope of inch per foot (5%). c) sidewalk shall be 4-foot minimum width when placed at an offset behind the curb, and 5-foot minimum width when placed adjacent to the curb. d) sidewalks and ramps shall be constructed of 4 thick concrete reinforced with 6 x 6 no. 6 gage wire mesh or no. 3 bars @ 8 o.c.e.w. e) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness f) sand backfill required on all sidewalks 3 max. sub-grade shall be compacted to 90% standard proctor. g) contraction joints shall be scored every 6 feet and expansion joints every 30 feet. h) sidewalk shall have a broom finish transverse to the walkway. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) no colored or stained or stamped concrete on city row sidewalks j) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. k) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. l) curb and gutter must be saw cut m) ramps shall be placed at all intersection with roadways or where required by law. l) flatwork is required to meet texas accessibility standards (texas civil statutes, article 9102). any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. additionally, decorative concrete shall require approval of the pattern and finish from the city engineer, or designee, prior to construction

Client: Floyd M & Yolanda M Morales

Parcel #: E556000000001400

Permit #: ROW2011-04091

Contractor: Smart Signs & Designs

Date: Jun 24, 2011

Permit type: Commercial Contracting

Description: New wall sign ( sprouting new beginnings rehab center)

Fee: $66.50 paid to City of Mcallen, Texas

Client: Properties Llc Milagro

Parcel #: I600001001001100

Permit #: SGN2011-04109

Date: Jun 30, 2011

Permit type: Commercial Contracting

Description: Tgs contractor will placing 2500 ft. of gas line along the north side of military hwy begining at international pwy to taylor rd ( city limits)

Client: Commercial Net Lease Realty Lp

Parcel #: S300400000000100

Permit #: ROW2011-04225

Date: Jul 7, 2011

Permit type: Commercial Contracting

Description: . sidewalks a) sidewalk alignment must match existing alignment in area or be set a minimum of five-foot from the back of curb. any deviation shall require approval by the city engineer. b) sidewalk shall slope toward the street with a maximum transverse slope of inch per foot (2%), 1-inch above the top of curb, and a maximum longitudinal slope of inch per foot (5%). c) sidewalk shall be 4-foot minimum width when placed at an offset behind the curb, and 5-foot minimum width when placed adjacent to the curb. d) sidewalks and ramps shall be constructed of 4 thick concrete reinforced with 6 x 6 no. 6 gage wire mesh or no. 3 bars @ 8 o.c.e.w. e) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness f) sand backfill required on all sidewalks 3 max. sub-grade shall be compacted to 90% standard proctor. g) contraction joints shall be scored every 6 feet and expansion joints every 30 feet. h) sidewalk shall have a broom finish transverse to the walkway. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) no colored or stained or stamped concrete on city row sidewalks j) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. k) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. l) curb and gutter must be saw cut m) ramps shall be placed at all intersection with roadways or where required by law. l) flatwork is required to meet texas accessibility standards (texas civil statutes, article 9102). any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. additionally, decorative concrete shall require approval of the pattern and finish from the city engineer, or designee, prior to construction residential driveway apron (a) minimum driveway width allowed is 12 ft. and maximum is 25 ft. b) curb cut must be a minimum of 6-feet from a side property line. c) flow line of new gutter shall match existing flow line. d) curb and gutter must be saw cut. e) driveway aprons shall be constructed of concrete with a minimum of 6 inches in thickness, reinforced with 6 x 6 no. 6 wire mesh, no. 3 bars @ 12 o.c.e.w. or no. 4 bars @ 18 o.c.e.w. f) no colored or stained or stamped concrete on city driveway apron g) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness. h) concrete shall have a broom finish. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. j) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. k) sub-grade shall be compacted to 90% standard proctor. l) expansion joint required at property line and intersection with sidewalks. longitudinal expansion joint required at mid-point of driveway if width is greater than 18 feet. m) if a manhole falls within a driveway pad, the manhole lid shall be placed flush with the elevation of the driveway. n) any driveway placed where a drainage bar ditch exists, shall maintain the flow line of the ditch with the placement of a concrete culvert. o) driveway wings shall not exceed a 12:1 slope. p) respect the transverse slope of 2% maximum where the sidewalk crossing is proposed. any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. q) requirements of plat note slope of 1%. in no instance shall site grading on residential or commercial properties adversely affect neighboring properties.

Client: Luis Luengas

Parcel #: S187000000000900

Permit #: ROW2011-04372

Contractor: 1-Stop A/C, Heating & Refrigeration

Date: Jul 22, 2011

Permit type: Commercial Contracting

Description: As per rg/mc, ok for automatic transfer switch for generater blueprint

Fee: $32.00 paid to City of Mcallen, Texas

Parcel #: M192000000000100

Permit #: CMM2011-04748

Date: Jul 28, 2011

Permit type: Commercial Contracting

Description: Commercial moving bldg legal: balboa acres lt 10 blk 10 = parcel under: 3408 idela ave

Valuation: $300,000

Fee: $133.00 paid to City of Mcallen, Texas

Client: St Joseph The Worker Church

Parcel #: B030000031000100

Permit #: MOV2011-04894

Contractor: T Mobile

Date: Jul 29, 2011

Permit type: Commercial Contracting

Description: Existing cell tower addition (cabinets, and install fiber to cabinet) no blueprint

Valuation: $750,000

Fee: $46.00 paid to City of Mcallen, Texas

Client: T Mobile

Permit #: CMM2011-04905

Date: Jul 29, 2011

Permit type: Commercial Contracting

Description: . sidewalks a) sidewalk alignment must match existing alignment in area or be set a minimum of five-foot from the back of curb. any deviation shall require approval by the city engineer. b) sidewalk shall slope toward the street with a maximum transverse slope of inch per foot (2%), 1-inch above the top of curb, and a maximum longitudinal slope of inch per foot (5%). c) sidewalk shall be 4-foot minimum width when placed at an offset behind the curb, and 5-foot minimum width when placed adjacent to the curb. d) sidewalks and ramps shall be constructed of 4 thick concrete reinforced with 6 x 6 no. 6 gage wire mesh or no. 3 bars @ 8 o.c.e.w. e) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness f) sand backfill required on all sidewalks 3 max. sub-grade shall be compacted to 90% standard proctor. g) contraction joints shall be scored every 6 feet and expansion joints every 30 feet. h) sidewalk shall have a broom finish transverse to the walkway. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) no colored or stained or stamped concrete on city row sidewalks j) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. k) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. l) curb and gutter must be saw cut m) ramps shall be placed at all intersection with roadways or where required by law. l) flatwork is required to meet texas accessibility standards (texas civil statutes, article 9102). any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. additionally, decorative concrete shall require approval of the pattern and finish from the city engineer, or designee, prior to construction residential driveway apron (a) minimum driveway width allowed is 12 ft. and maximum is 25 ft. b) curb cut must be a minimum of 6-feet from a side property line. c) flow line of new gutter shall match existing flow line. d) curb and gutter must be saw cut. e) driveway aprons shall be constructed of concrete with a minimum of 6 inches in thickness, reinforced with 6 x 6 no. 6 wire mesh, no. 3 bars @ 12 o.c.e.w. or no. 4 bars @ 18 o.c.e.w. f) no colored or stained or stamped concrete on city driveway apron g) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness. h) concrete shall have a broom finish. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. j) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. k) sub-grade shall be compacted to 90% standard proctor. l) expansion joint required at property line and intersection with sidewalks. longitudinal expansion joint required at mid-point of driveway if width is greater than 18 feet. m) if a manhole falls within a driveway pad, the manhole lid shall be placed flush with the elevation of the driveway. n) any driveway placed where a drainage bar ditch exists, shall maintain the flow line of the ditch with the placement of a concrete culvert. o) driveway wings shall not exceed a 12:1 slope. p) respect the transverse slope of 2% maximum where the sidewalk crossing is proposed. any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. q) requirements of plat note slope of 1%. in no instance shall site grading on residential or commercial properties adversely affect neighboring properties.

Client: Landmark Valley Homes Inc

Parcel #: M319700000010900

Permit #: ROW2011-04900

Date: Aug 4, 2011

Permit type: Commercial Contracting

Description: Traffic light control mcallen sw ind dist #5 lot 6a

Permit #: CMM2011-05077

Date: Aug 4, 2011

Permit type: Commercial Contracting

Description: Traffic light control mcallen sub citrus groves lt 27 bloc 1 & lots 183-185 & lots 188-190 la lomita 148.62 acres

Permit #: CMM2011-05074

Date: Aug 4, 2011

Permit type: Commercial Contracting

Description: . sidewalks a) sidewalk alignment must match existing alignment in area or be set a minimum of five-foot from the back of curb. any deviation shall require approval by the city engineer. b) sidewalk shall slope toward the street with a maximum transverse slope of inch per foot (2%), 1-inch above the top of curb, and a maximum longitudinal slope of inch per foot (5%). c) sidewalk shall be 4-foot minimum width when placed at an offset behind the curb, and 5-foot minimum width when placed adjacent to the curb. d) sidewalks and ramps shall be constructed of 4 thick concrete reinforced with 6 x 6 no. 6 gage wire mesh or no. 3 bars @ 8 o.c.e.w. e) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness f) sand backfill required on all sidewalks 3 max. sub-grade shall be compacted to 90% standard proctor. g) contraction joints shall be scored every 6 feet and expansion joints every 30 feet. h) sidewalk shall have a broom finish transverse to the walkway. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) no colored or stained or stamped concrete on city row sidewalks j) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. k) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. l) curb and gutter must be saw cut m) ramps shall be placed at all intersection with roadways or where required by law. l) flatwork is required to meet texas accessibility standards (texas civil statutes, article 9102). any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. additionally, decorative concrete shall require approval of the pattern and finish from the city engineer, or designee, prior to construction residential driveway apron (a) minimum driveway width allowed is 12 ft. and maximum is 25 ft. b) curb cut must be a minimum of 6-feet from a side property line. c) flow line of new gutter shall match existing flow line. d) curb and gutter must be saw cut. e) driveway aprons shall be constructed of concrete with a minimum of 6 inches in thickness, reinforced with 6 x 6 no. 6 wire mesh, no. 3 bars @ 12 o.c.e.w. or no. 4 bars @ 18 o.c.e.w. f) no colored or stained or stamped concrete on city driveway apron g) bar-lift plastic chairs, or approved equal, shall be used to secure steel at center of concrete thickness. h) concrete shall have a broom finish. exposed aggregate, pavers, tile and stained or painted concrete are not permitted within the right of way. i) all concrete shall be 5-sack concrete and shall have a minimum compressive strength of 3000 psi. j) membrane curing compound shall be applied at a minimum of 1 gallon per 180 square feet of area. k) sub-grade shall be compacted to 90% standard proctor. l) expansion joint required at property line and intersection with sidewalks. longitudinal expansion joint required at mid-point of driveway if width is greater than 18 feet. m) if a manhole falls within a driveway pad, the manhole lid shall be placed flush with the elevation of the driveway. n) any driveway placed where a drainage bar ditch exists, shall maintain the flow line of the ditch with the placement of a concrete culvert. o) driveway wings shall not exceed a 12:1 slope. p) respect the transverse slope of 2% maximum where the sidewalk crossing is proposed. any admixtures to the concrete mix (i.e. fiber mesh, plasticizers, etc.) shall require approval. q) requirements of plat note slope of 1%. in no instance shall site grading on residential or commercial properties adversely

Client: Boby Llc

Parcel #: E015400000012000

Permit #: ROW2011-05061

Date: Aug 4, 2011

Permit type: Commercial Contracting

Description: Traffic light control idela park #3 lot 64- unit 3

Permit #: CMM2011-05076

Contractor: Reynos Electric Service

Date: Aug 5, 2011

Permit type: Commercial Contracting

Description: Commerical office/warehouse remodel (adding a demising wall and seperation of electrical service) no blueprints note: parcel under 4401 wanda

Valuation: $5,500,000

Fee: $81.00 paid to City of Mcallen, Texas

Client: Ridge Cbf Mcallen Llc

Parcel #: S300402000000300

Permit #: CMM2011-05091

Contractor: Marios Electric

Date: Aug 9, 2011

Permit type: Commercial Contracting

Description: New canopy structures for shade one blueprints

Fee: $32.00 paid to City of Mcallen, Texas

Client: City Of Mcallen

Permit #: CMM2011-05169

Contractor: Metro Electric, Inc

Date: Aug 12, 2011

Permit type: Commercial Contracting

Description: Office -rehab center no blueprints (penalty as per robert /juan/eek)

Fee: $46.00 paid to City of Mcallen, Texas

Client: 2009 Industrial Dr

Parcel #: M217000000000900

Permit #: CMM2011-05257

Contractor: A1 Skylite Signs Llc

Date: Aug 15, 2011

Permit type: Commercial Contracting

Description: Pole sign " supercuts"

Fee: $66.50 paid to City of Mcallen, Texas

Client: Hd Development Properties Lp

Parcel #: H422700000000100

Permit #: SGN2011-05288